4CH Transmitter Module Long Range Remote Control 300-4000m + DC12V 4CH Relay Receiver

MOD-030
14 In stock
R 467.69
Transmitter  Working Voltage :DC9V Working Frequency :433.92Mhz Optional by leaving massage Working Current :100mA Transmitting Rate :<10KbpsWorking Temperature : -10'c~+70'c Pin:13 12 11 10 9V GND Size :49×30×6mm Code :Fixed Code  SC2262  IC Chip Transmitting Distance:+-4000m Line of sight DC12V 4CH Receiver Board 1.Working Voltage: DC12V -/+ 10%2.Current:Standby≤10mA,Working ≤128mA3.Working Temperature: -10'C—+60'C4.Receiver Frequency: 433.92MHZ5.Receiving Sensitivity: -105dB6.Output State: Switching Value7.Max Load:10A Relay,...
R 467.69
Terms & conditions

Transmitter 

Working Voltage :DC9V
Working Frequency :433.92Mhz Optional by leaving massage
Working Current :100mA
Transmitting Rate :<10Kbps
Working Temperature : -10'c~+70'c
Pin:13 12 11 10 9V GND
Size :49×30×6mm
Code :Fixed Code  SC2262  IC Chip
Transmitting Distance:+-4000m Line of sight

DC12V 4CH Receiver Board

1.Working Voltage: DC12V -/+ 10%
2.Current:Standby≤10mA,Working ≤128mA
3.Working Temperature: -10'C—+60'C
4.Receiver Frequency: 433.92MHZ
5.Receiving Sensitivity: -105dB
6.Output State: Switching Value
7.Max Load:10A Relay, Resistive load≤8A,Inductive load≤3A
8.Receiver Board Size:68×48×13mm
9.Case Size:75×55×30mm

Encoding Type: Learning Code, Add transmitter by the Learning Button on the receiver

Output State: It is adjusted by the Jumper on the Receiver Board,

Momentary----------Take away the Jumper or put the Jumper on 1 Pin

Toggle----------------Jumper “ T & Mid Pin ”

Latched--------------Jumper on “ M & Mid Pin ”

 Momentary------------Press the Transmitter button A, the receiver relay A is ON, release button A; the receiver relay A is OFF, the same as B/C/D. 4CH are independent.

 Toggle---------------Press transmitter button A for 1 time, the receiver relay A is ON, press button A again, the receiver relay A is OFF, the same as B/C/D. 4CH are independent.

 Latched------------------

Press transmitter button A, the receiver relay A is ON, the relay B/C/D is OFF.

Press transmitter button B, the receiver relay B is ON, the relay A/C/D is OFF.

Press transmitter button C, the receiver relay C is ON, the relay A/B/D is OFF

Press transmitter button D, the receiver relay D is ON, the relay A/B/C is OFF.

It also mean .Latched only can keep 1CH ON .and it will often have 1CH is ON.

Learning Method:
Input power to the Receiver .Press the Learning Button Once the LED will go OFF . Then press transmitter any Button, the Led indicator will flash ON, then when you press any button of the transmitter ,you should hear the relay respond ,it means learning was successful.


Clearing Code

Press and hold the Learning Button on the receiver until the LED indicator turns OFF and when erasing will give you a flashing indication and stays ON, it means the code has been cleared successfully.

Write a review
| Ask a question
Write a review
| Ask a question
The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.
4CH Transmitter Module Long Range Remote Control 300-4000m + DC12V 4CH Relay Receiver
You have successfully subscribed!
This email has been registered